Repair of Opel Corsa C, from 2000 to 2005 release.
1. Operation and maintenance of the car
2. Engine
3. Transmission
3.1. Coupling
3.2. Mechanical box передч
3.3. Automatic transmission
3.3.1. General information
3.3.2. Hydrotransformer
3.3.3. Main transfer
3.3.4. Adjustment of a cable of the selector of switching of automatic transmission
3.3.5. Designation of the automatic transmission (AF 13-II)
3.3.6. Check of a condition of gearbox oil (AF13-II)
3.3.7. Check of pressure of oil (AF13-II)
3.3.8. Check of the position switch of the lever of gear shifting (AF13-II)
3.3.9. Unblocking of a stopper of the lever of gear shifting at violation of its work
3.3.10. Adjustment of the position switch of the lever of gear shifting (AF13-II)
3.3.11. Adjustment of hummock system of the drive of gear shifting (AF13-II)
3.3.12. Replacement of hummock system of the drive of gear shifting (AF13-II)
3.3.13. Replacement of the switch of lock adaptation of the lever of gear shifting
3.3.14. Replacement of a plait of wires in knot of the lever of gear shifting (AF13-II)
3.3.15. Replacement of the control unit of the electronic switch of the check point
3.3.16. Replacement of the glow lamp of the indicator of gear shifting in the console of the lever of gear shifting (AF 13-II)
3.4. Driving mechanism
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment
 





0653563c

3-3-10-regulirovka-pozicionnogo-pereklyuchatelya-rychaga-pereklyucheniya-peredach-af13-ii.html

3.3.10. Adjustment of the position switch of the lever of gear shifting (AF13-II)

Dismantle the holder of the socket of a plait of wires 2.
Release and disconnect the socket of a plait of wires of the position switch of the lever of gear shifting 1.
Wring out from a control lever a cable of the drive of gear shifting 3.
Install KM-962-A devices with KM-962-10.
Connect to the socket of a plait of wires of the position switch of the lever of gear shifting.
Connect to the accumulator.
Transfer the gear shifting lever by rotation of a control lever 2 to neutral situation.

NOTE
First of all, the lever of gear shifting needs to be turned to the left against the stop (in the direction of the movement), right after it to turn back on 2 lock positions ("P", "R", "N"). For position of the N lever the light-emitting diodes corresponding to marks in the sliding table have to light up.

For adjustment turn off lock screws 1.

NOTE
Turn the position switch of the lever of gear shifting so that all light-emitting diodes corresponding to position of the N lever lit up.

Tighten lock screws – 25 N · m.

NOTE
Make switching consistently of all transfers by turn of a control lever. For each separate position of the lever of gear shifting the light-emitting diodes corresponding to marks have to light up. If necessary repeat the procedure of adjustment.

Dismantle KM-962-A devices with KM-962-10.
Disconnect from the accumulator.
Disconnect from the socket of a plait of wires of the position switch of the lever of gear shifting.
Install the socket of a plait of wires of the position switch of the lever of gear shifting 1.
Attach and fix the socket of a plait of wires.
Delay fastening of the socket of a plait of wires of 2-20 N · m.
Establish a hummock wire of system of the drive of gear shifting 3 on a control lever of the position switch of the lever of gear shifting.

"on the page back
3.3.9. Unblocking of a stopper of the lever of gear shifting at violation of its work
on the following page"
3.3.11. Adjustment of hummock system of the drive of gear shifting (AF13-II)