Repair of Opel Corsa C, from 2000 to 2005 release.
1. Operation and maintenance of the car
2. Engine
2.1. Petrol Z10XE, Z10XEP, Z12XE, Z12XEP DOHC-I engines
2.1.1. Number of the engine
2.1.2. Check of pressure of oil (Z10XE, Z10XEP)
2.1.3. Check of a compression of the engine (Z10XE, Z10XEP)
2.1.4. Check of phases of gas distribution (Z10XE, Z10XEP, without conditioner)
2.1.5. Check of pressure of compression (Z10XE, Z10XEP, with the conditioner)
2.1.6. Check of pressure of fuel (Z10XE, Z10XEP, with the conditioner)
2.2. Mechanical part of petrol Z10XE, Z10XEP, Z12XE, Z12XEP DOHC-I engines
2.3. Cooling system
2.4. Lubrication system
2.5. System of injection
2.6. Petrol engines – the general procedures of check
2.7. Mechanical part of the engine
2.8. Test and repair operations of components of a mechanical part of the engine
2.9. Cooling system
2.10. System of injection of fuel of petrol engines
2.11. Lubrication system
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment
 















0653563c

2-1-4-proverka-faz-gazoraspredeleniya-z10xe-z10xep-bez-kondicionera.html

2.1.4. Check of phases of gas distribution (Z10XE, Z10XEP, without conditioner)

Open a cowl
Disconnect plugs of the rechargeable battery

NOTE
On cars since a year of release 04 with ESP – after each detachment of the accumulator the sensor of an angle of rotation of a steering wheel loses the main installation. It needs to be calibrated anew.

Disconnect a weight wire.
Disconnect 4 sockets of a plait of wires of a control system of the engine: oil 2 pressure relay, sensor of temperature of cooling liquid 3, sensor of the camshaft 4, module of ignition 1.
Free the canal for a plait of wires 5.
Put a plait of wires aside.
Dismantle the ignition module.
Uncover the ignition module, shift it to the right.
Turn off 2 bolts of fastening.
Take out a cover by means of KM-6009 adaptation.

NOTE
Do not warp the provision of a cover.

Uncover a head of cylinders.
Dismantle 2 hoses of ventilation of a case of the engine.
Turn off 13 bolts of fastening of fastening.
Lift the car.
On the ECO model uncover the engine below.
Remove a carving stopper of a support of a bent shaft 1.
Lower the car.
Establish the provision of VMT of ignition of the cylinder 1.
Insert the KM-952 2 device.
Evenly turn a bent shaft until KM-952 adaptation is captured.

NOTE
The mark in a belt pulley of a bent shaft 4 has to be on one line with a lug 3 on the GRM case.

Insert the KM-9531 device, it has to enter a groove of camshafts.

NOTE
If it is impossible to insert the KM-953 device, then it is necessary to execute the main adjustment of phases of gas distribution.

Install KM-9541 adaptation. Get on a disk of the phase sensor 2.

NOTE
KM-954 has to enter a groove of a disk of the phase sensor.

Take out the fixing tools.

NOTE
The fixing tools cannot be used for keeping.

Lift the car.
Establish a carving stopper of a support of a bent shaft.
Replace a sealing ring.
Tighten a bolt the moment of 50 N · m.
Lower the car.
On the ECO model establish an engine cover below.
Clean sealing surfaces of a head of cylinders and a cover of a head of cylinders.
Establish a cover of a head of cylinders 1.
Replace consolidation 2 and a sealing ring.
Apply sealant (distance of 1-2 mm).

NOTE
Installation works need to be finished within 10 min.

Tighten 13 bolts of fastening the moment of 8 N · m.
Establish 2 hoses of ventilation of a case of the engine.
Install the ignition module.
Turn off 2 KM-6009 devices.
Tighten 2 bolts of fastening with the moment of 8 N · m.
Establish a plait of wires of a control system of the engine.
Lay a plait of wires.
Fix the channel for a plait of wires.
Connect 4 sockets of a plait of wires.
Connect plugs of the rechargeable battery.
Program volatile memory.
Close a cowl.

"on the page back
2.1.3. Check of a compression of the engine (Z10XE, Z10XEP)
on the following page"
2.1.5. Check of pressure of compression (Z10XE, Z10XEP, with the conditioner)