|
2-1-3-proverka-kompressii-dvigatelya-z10xe-z10xep.html
2.1.3. Check of a compression of the engine (Z10XE, Z10XEP)Procedure of check
Open a cowl
Remove the case of the air filter 1.
For this purpose disconnect 2 sockets of a plait of wires, a termoanemometrichesky film mass flowmeter of air 3, the valve of ventilation of a tank 2.
Release the valve of ventilation of a tank.
Dismantle the soaking-up branch pipe 4.
For this purpose turn off 2 nuts.
Dismantle a hose of ventilation of a case of the engine 5.
On Z10XEP: remove the soaking-up air hose, release a collar and unscrew a bolt (shooter).
Dismantle the ignition module.
Uncover the ignition module.
|
NOTE
Shift it to the right.
|
Disconnect the socket of a plait of wires.
Turn off 2 bolts of fastening.
Take out the module by means of special KM-6009 adaptation.
|
NOTE
Do not warp the provision of a cover.
|
Turn out 3 spark plugs using KM-1 94-E adaptation.
Lift the car.
Remove a casing of a poliklinovy belt.
For what unscrew 3 bolts of fastening 1.
Remove a clip (shooter).
Lower the car.
Establish the provision of VMT of ignition of the cylinder 1.
|
NOTE
Marking of a pulley of a bent shaft has to be on one line with a lug on the GRM case.
|
Apply on a belt pulley auxiliary marks with shift on 120 ° to cylinder 1 ignition mark VMT.
Turn off a cover of an oil-filling branch pipe.
|
NOTE
Marking of a pulley of a bent shaft has to be on one line with a lug on the GRM case.
|
|
ATTENTION
Open a cover of a compensation tank of cooling liquid carefully and slowly since there is a danger of a burn.
|
Turn off a cover of a compensation tank of cooling liquid
Pull out the oil meter probe.
|
NOTE
Pay attention to the sufficient length of the adapter. Connection of the adapter has to be easily available. Do not damage a spark plug carving.
|
Install the adapter and the measuring instrument of pressure drop on the cylinder 1.
Include transfer and tighten the parking brake
|
NOTE
All wheels have to concern a basic surface.
|
Check pressure drop on the cylinder 1.
|
NOTE
Observe instructions of the manufacturer.
|
Check pressure drop of the engine in other cylinders.
Establish the provision of VMT of the cylinder 2.
Rearrange the adapter and the measuring instrument of pressure drop on the cylinder 2.
Check pressure drop on the cylinder 2.
Establish the provision of VMT of the cylinder 3.
Rearrange the adapter and the measuring instrument of pressure drop on the cylinder 3.
Check pressure drop on the cylinder 3.
Remove the pressure drop measuring instrument.
Establish the provision of idling.
Dismantle the adapter from the cylinder 3.
Establish spark plugs.
By means of special KM-194-E adaptation tighten 3 pieces with the moment of 25 N · m.
Install the ignition module.
Tighten 2 bolts of fastening with the moment of 8 N · m.
Connect the socket of a plait of wires.
Establish an ignition module cover.
Insert the oil meter probe.
Twirl a cover of a compensation tank of cooling liquid.
Twirl a cover of an oil-filling branch pipe.
Install the case of the air filter. Tighten a bolt.
On Z10XEP engines: establish the soaking-up air hose and tighten a collar the moment of 3,5 N · m.
Fix the soaking-up branch pipe.
Replace a sealing ring.
Tighten 2 nuts the moment of 8 N · m.
Establish a hose of ventilation of a case of the engine. Connect the valve of ventilation of a tank, connect 2 sockets of a plait of wires
Lift the car.
Establish a casing of a poliklinovy belt.
Twirl 3 bolts of fastening.
Establish a clip.
Lower the car.
Close a cowl.
| 