Repair of Opel Corsa C, from 2000 to 2005 release.
1. Operation and maintenance of the car
2. Engine
2.1. Petrol Z10XE, Z10XEP, Z12XE, Z12XEP DOHC-I engines
2.2. Mechanical part of petrol Z10XE, Z10XEP, Z12XE, Z12XEP DOHC-I engines
2.3. Cooling system
2.4. Lubrication system
2.5. System of injection
2.5.1. Replacement of fuel nozzles (one or all) (Z10XE, Z10XEP, without conditioner)
2.5.2. Replacement of the fuel filter (petrol engines)
2.5.3. Removal and installation of the electric fuel pump
2.5.4. Replacement of consolidation of a final collector (Z10XE, Z10XEP, without conditioner)
2.6. Petrol engines – the general procedures of check
2.7. Mechanical part of the engine
2.8. Test and repair operations of components of a mechanical part of the engine
2.9. Cooling system
2.10. System of injection of fuel of petrol engines
2.11. Lubrication system
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment
 





0653563c

2-5-2-zamena-toplivnogo-filtra-benzinovye-dvigateli.html

2.5.2. Replacement of the fuel filter (petrol engines)

Removal
Remove an air duct guard from the bottom of a body of Century.
Release the fuel filter in the holder.
Remove a bolt 1.

NOTE
In drawings the model Combo option (F06, F25) is shown.

Install a head of the special tool 1 on the fuel filter 2.
The carving union 3 specifies down.
Press all surface of rubber consolidation (shooter) the case of the fuel filter.
Adjust as appropriate a coupler.
Tighten it a tightening bracket.
Install a vessel for collecting fuel 3 on a head of the special tool 1.

ATTENTION
The fuel filter is under pressure. Check the special tool for landing durability.

Fix a vessel for collecting fuel on a carving branch pipe and to tighten.

NOTE
The built-in drill bores through the case of the fuel filter. The following fuel flows down in a reception vessel.

Blow the fuel filter.

ATTENTION
Observe the set sequence.

By means of the pincers 5 attached to the special tool make wider opening (shooter) above.
Remove from the fuel filter and cork 2 fuel-supply lines (2, 4).

ATTENTION
Remove fuel-supply lines only when fuel is not produced from the fuel filter any more.

Dismantle by means of KM-796-A adaptation from quick disconnect connection.
Cork a fuel-supply line by means of KM-807 adaptation.
When the fuel filter is emptied, remove the special tool.
Remove a reception vessel.
Remove a head of the special tool – weaken a tension collar.
Remove the fuel filter.

Installation
Insert 2 new connecting clips 1 into the plug of a high-speed lock of a fuel-supply line 2.
Insert the new fuel filter.
Insert in front in the holder.

NOTE
Observe the throughput direction.

Connect 2 fuel-supply lines (4, 5) to the fuel filter.
Snimitespetsialny KM-807 adaptation.
Connect 2 fuel-supply lines by means of a high-speed lock to the fuel filter.
Carry out test on stretching.

NOTE
Make sure that high-speed locks were correctly recorded.

Fix the fuel filter in the holder.
Establish a bolt 3 and tighten its moment 4 N · m.
Establish an air duct guard on the body bottom.

For model option of "ECO"
At the working engine check 2 high-speed locks of a fuel-supply line in the fuel filter for tightness.

"on the page back
2.5.1. Replacement of fuel nozzles (one or all) (Z10XE, Z10XEP, without conditioner)
on the following page"
2.5.3. Removal and installation of the electric fuel pump