Repair of Opel Corsa C, from 2000 to 2005 release.
1. Operation and maintenance of the car
2. Engine
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
8.1. Features of a design
8.2. Hinged elements
8.2.1. Removal and installation of a front bumper
8.2.2. Removal and installation of the holder of a forward beam (blow limiter)
8.2.3. Replacement covered
8.2.4. Removal and installation of a protective covering in a wing
8.2.5. Removal and installation of a rear bumper
8.2.6. Removal and installation of a molding of an entrance aperture
8.2.7. Removal and installation of a forward protective level
8.2.8. Removal and installation of a water repeller
8.2.9. Replacement of additional consolidation of a frame of a roof
8.2.10. Removal and installation of a cowl
8.2.11. Removal and installation of the lock of a forward door
8.2.12. Removal and installation of the external handle of a forward door
8.2.13. Replacement of a guide of glass of a lifting window of a forward door
8.2.14. Removal and installation of an internal covering of a forward door
8.2.15. Remove and establish a level of a crack of a window regulator of a forward / back door inside
8.2.16. Removal and installation of a bracket of the lock of a forward door
8.2.17. Removal and installation of consolidation of a forward door
8.2.18. Removal and installation of a back door
8.2.19. Removal and installation of an internal covering of a back door
8.2.20. Removal and installation of consolidation of a back door
8.2.21. Removal and installation of a back folding door
8.2.22. Removal and installation of the lock of a back folding door
8.2.23. Removal and installation of the external handle of a back folding door
8.2.24. Removal and installation of a pneumatic spring of a back folding door
8.2.25. Removal and installation of consolidation of a back folding door
8.2.26. Removal and installation of an internal covering of a back folding door
8.2.27. Removal and installation of consolidation flew down in a back folding door
8.2.28. Replacement of an element of management of the external rear-view mirror regulated from within
8.3. Body glazing
9. Schemes of electric equipment
 





0653563c

8-2-10-snyatie-i-ustanovka-kapota.html

8.2.10. Removal and installation of a cowl

Removal
Dismantle a cowl.
When replacing the hinge: dismantle a water repeller.
Uncover the block of the relay of the module of management of electronic systems of a body.

Installation
When replacing a cover of a cowl, establish isolation.
Adjust a cowl to a wing.
Adjustment of a gap 3 is carried out in points of screwing up 1, and adjustment on height – in points of screwing up 2.
1 – Points of screwing up of a cowl.
2 – Points of screwing up of the hinge of a cowl.
Flatten the end of a rivet by means of nippers 2.
Adjust locking.
Adjusting size (X) = 40–45 mm.
Zakontrite a round nut in the following sequence: The 5th round nut, the 6th twisted spring, the 7th washer, 8 directing pin.
The moment of an inhaling of a round nut and the directing pin – 22 N · m.

NOTE
Grease the directing pin.

Removal and installation of a forward door

Removal
Disconnect the socket of a plait of wires.
Dismantle a door.
Unscrew the fixing screw of fastening of the tape door limiter.
Dismantle tightening plugs of the door hinge.

NOTE
Apply lubricant of high pressure to lubricant of tightening plugs (number of a detail 90 510 336/number according to the catalog 19 48 606).

Installation
Establish a door.
If necessary adjust a forward door.

NOTE
Observe adjusting gaps.

Adjusting gaps

NOTE
The sizes of a gap concern the varnished door lobby in a set with all mounted details.

"on the page back
8.2.9. Replacement of additional consolidation of a frame of a roof
on the following page"
8.2.11. Removal and installation of the lock of a forward door