Repair of Opel Corsa C, from 2000 to 2005 release.
1. Operation and maintenance of the car
2. Engine
2.1. Petrol Z10XE, Z10XEP, Z12XE, Z12XEP DOHC-I engines
2.2. Mechanical part of petrol Z10XE, Z10XEP, Z12XE, Z12XEP DOHC-I engines
2.3. Cooling system
2.4. Lubrication system
2.4.1. Removal and installation of the case of an oil filter (Z10XE, Z10XEP, without conditioner)
2.4.2. Replacement of engine oil (Z10XE, Z10XEP)
2.4.3. Removal and installation of the oil pallet (Z10XE, Z10XEP, without conditioner)
2.4.4. Replacement of the relay of pressure of oil (Z10XE, Z10XEP)
2.5. System of injection
2.6. Petrol engines – the general procedures of check
2.7. Mechanical part of the engine
2.8. Test and repair operations of components of a mechanical part of the engine
2.9. Cooling system
2.10. System of injection of fuel of petrol engines
2.11. Lubrication system
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment
 





0653563c

2-4-1-snyatie-i-montazh-korpusa-maslyanogo-filtra-z10xe-z10xep-bez-kondicionera.html

2.4.1. Removal and installation of the case of an oil filter (Z10XE, Z10XEP, without conditioner)

NOTE
On cars since a year of release 04 with ESP – after each detachment of the accumulator the sensor of an angle of rotation of a steering wheel loses the main installation. It needs to be calibrated anew.

Lubricant contour
* The engine is heated-up and idles

Lubricant contour
* The engine is heated-up and idles

Removal
Open a cowl.
Disconnect plugs of the rechargeable battery.
Disconnect a weight wire.
Dismantle heated a lambda sensor of regulation of composition of fuel mix.
Disconnect the socket of a plait of wires.
Release a plait of wires.
Carefully turn out by means of KM-61291 adaptation.
Dismantle a transport earring of the engine 2 at the left.
Turn out a bolt.
Dismantle a guard of a final collector.
Turn off 3 bolts of fastening.
Turn the directing tube of the probe of an oil meter forward.
Uncover the case of an oil filter.

NOTE
On option of the ECO model uncover motor office below.

Substitute the reception pallet.
Remove the case of an oil filter.
Turn off 3 bolts of fastening (arrow).
Clean the sealing surfaces of the case of an oil filter, the block of cylinders.

Installation
Install the case of an oil filter.
Replace consolidation.
Tighten bolts the moment of an inhaling of 20 N · m.
Establish a cover of the case of an oil filter.
Replace a sealing ring.
Tighten bolts of fastening of a cover the moment of 10 N · m.
Establish a guard of a final collector.
Establish the directing oil meter probe tube.
Tighten 3 bolts of fastening the moment of 8 N · m.
Establish a transport earring of the engine at the left.
Establish heated a lambda sensor of regulation of composition of fuel mix.
Apply on a carving assembly paste (white).
Tighten a lambda sensor the moment 40 N · m.
Attach the socket of a plait of wires.
Fix a plait of wires.
On option of the ECO model establish a cover of motor office below.
Connect plugs of the rechargeable battery.
Program volatile memory.
Close a cowl.

"on the page back
2.4. Lubrication system
on the following page"
2.4.2. Replacement of engine oil (Z10XE, Z10XEP)